-
Our Control Station Combiners (CSC) is an ideal solution to reduce the number of antennas required on a communications site by maintaining a high radio-to-radio isolation at all times. It can significantly reduce tower clutter and loading, and simplify cabling installation at control center facilities. This product provides frequency-agile operation across a frequency range from 380 up to 512 MHz. This combiner has the possibilities to be connected to two antennas TX and RX. In case of only one antenna is used for TX and RX, an external duplexer is required. DOWNLOAD PDF
-
Our line of radome transit antennas for operation in the 806-960 MHz band consists of compact, low profile antennas in weatherproof ABS radomes. When mounted on a horizontal surface, maximum radiation is omnidirectional and vertically polarized. These antennas are an excellent choice for low clearance applications such as those found on trains, mass transit vehicles, construction equipment and police and emergency vehicles. The F-3758 model is a standard, folded radiator housed in a sturdy high-impact ABS radome. To ensure a moisture proof installation, the F-3758 model is supplied with a mounting gasket. DOWNLOAD PDF
-
The 440-70-HDBP*3 is Heavy Duty, Black Anodized, Low PIM Corner Reflector Antenna. This antenna has a very high front-to-back ratio. It is broadband and is ideal for point-to-point applications. Performance is constant throughout the band. The antenna has a rugged design to withstand harsh environmental conditions.
- The mounting hardware supplied will permit either vertical or horizontal polarization
- DC ground for lightning protection
-
F-3990 This VHF antenna is designed for applications that require peak performance in the 136-174 MHz while tolerating a VSWR around 2.0:1. This antenna has a loading coil between the radiating element and the base. This coil increases the electrical length and makes the antenna perform electrically as a 1/4 wave antenna, but shorter than a regular 1/4 wave antenna. Typical gain, when mounted on a ground plane, is comparable to a full 1/4 wave. Mounts on NMO. The upper element is made from a brass wound cable with a flexible shaft core, well sealed using rubber shrink material. This solution offers a high reliability and prevents breakage or brittleness. Other frequencies are available upon request. DOWNLOAD PDF
-
The 290-70-EB is a VHF Yagi Antenna with extended boom.
- Each antenna has a rugged design to withstand harsh environmental conditions.
- The mounting hardware supplied will permit either vertical or horizontal polarization.
- DC ground for lightning protection.
- Heavy Duty and Black Anodized versions available.
-
The 290-70-HDEB is a VHF Yagi Antenna with extended boom.
- Each antenna has a rugged design to withstand harsh environmental conditions.
- The mounting hardware supplied will permit either vertical or horizontal polarization.
- DC ground for lightning protection.
- Black Anodized versions available.
-
The F-33029D-SM-1/4 is is a Wide Band Antenna with Black Anodized boom and dipoles. It is specifically designed for trunked Multicoupler such as X-pass systems. The 1/4 Wavelength dipole to mast spacing offers an offset radiation pattern. The antenna is made of Aluminium 6061-T6. This antenna is extremely rugged and is well suited for use in severe environmental conditions. This antenna is a Low Intermod design that incorporates a minimum of moveable joints in its construction and replaces standard castings with heavy duty welded joints. The F-33029D-SM-1/4 has internal cabling design and is not field adjustable.
- 1/2 wavelength dipole-to-mast spacing is also available for the bidirectional radiation pattern.
- 3/8 wavelength dipole-to-mast spacing is also available for a radiation pattern between the elliptic and the offset.
-
The F-33029D-SM-1/2 is is a Wide Band Antenna with Black Anodized boom and dipoles. It is specifically designed for trunked Multicoupler such as X-pass systems. The 1/2 Wavelength dipole to mast spacing offers a bidirectional radiation pattern. The antenna is made of Aluminium 6061-T6. This antenna is extremely rugged and is well suited for use in severe environmental conditions. This antenna is a Low Intermod design that incorporates a minimum of moveable joints in its construction and replaces standard castings with heavy duty welded joints. The F-33029D-SM-1/2 has internal cabling design and is not field adjustable.
- 1/4 wavelength dipole-to-mast spacing is also available for the offset radiation pattern.
- 3/8 wavelength dipole-to-mast spacing is also available for a radiation pattern between the elliptic and the offset.
-
The F-33029D-SM-3/8 is is a Wide Band Antenna with Black Anodized boom and dipoles. It is specifically designed for trunked Multicoupler such as X-pass systems. The 3/8 Wavelength dipole to mast spacing offers a radiation pattern between the elliptic and the offset. The antenna is made of Aluminium 6061-T6. This antenna is extremely rugged and is well suited for use in severe environmental conditions. This antenna is a Low Intermod design that incorporates a minimum of moveable joints in its construction and replaces standard castings with heavy duty welded joints. The F-33029D-SM-3/8 has internal cabling design and is not field adjustable.
- 1/4 wavelength dipole-to-mast spacing is also available for the offset radiation pattern.
- 1/2 wavelength dipole-to-mast spacing is also available for a bidirectional radiation pattern.
-
The F-33029D-TM-3/8 is is a Wideband Black Anodized Antenna. It is specifically designed for trunked Multicoupler such as X-pass systems. The 3/8 Wavelength dipole to mast spacing offers a radiation pattern between the elliptic and the offset. The antenna is made of Aluminium 6061-T6. This antenna is extremely rugged and is well suited for use in severe environmental conditions. This antenna is a Low Intermod design that incorporates a minimum of moveable joints in its construction and replaces standard castings with heavy duty welded joints. The F-33029D-TM-3/8 has internal cabling design and is not field adjustable.
- 1/4 wavelength dipole-to-mast spacing is also available for the offset radiation pattern.
- 1/2 wavelength dipole-to-mast spacing is also available for a bidirectional radiation pattern.
-
The F-33029D-TM-1/2 is is a Wideband Black Anodized Antenna. It is specifically designed for trunked Multicoupler such as X-pass systems. The 1/2 Wavelength dipole to mast spacing offers a bidirectional radiation pattern. The antenna is made of Aluminium 6061-T6. This antenna is extremely rugged and is well suited for use in severe environmental conditions. This antenna is a Low Intermod design that incorporates a minimum of moveable joints in its construction and replaces standard castings with heavy duty welded joints. The F-33029D-TM-1/2 has internal cabling design and is not field adjustable.
- 1/4 wavelength dipole-to-mast spacing is also available for the offset radiation pattern.
- 3/8 wavelength dipole-to-mast spacing is also available for a radiation pattern between the elliptic and the offset.
-
The F-33029D-TM-1/4 is is a Wideband Black Anodized Antenna. It is specifically designed for trunked Multicoupler such as X-pass systems. The 1/4 Wavelength dipole to mast spacing offers an offset radiation pattern. The antenna is made of Aluminium 6061-T6. This antenna is extremely rugged and is well suited for use in severe environmental conditions. This antenna is a Low Intermod design that incorporates a minimum of moveable joints in its construction and replaces standard castings with heavy duty welded joints. The F-33029D-TM-1/4 has internal cabling design and is not field adjustable.
- 1/2 wavelength dipole-to-mast spacing is also available for the bidirectional radiation pattern.
- 3/8 wavelength dipole-to-mast spacing is also available for a radiation pattern between the elliptic and the offset.